J9九游会AG

您当前的位置是:>>行业应用

精密点焊机电池行业应用


精密点焊机电池行业应用


      

       电池点焊机主要有如下特点:

  1、外形美观轻巧;

  2、焊接痕迹美观,火花小,无发黑(电池不会因点焊后出现凹陷、流液的现象),完全克服锂电池点焊后出现低压和出水现象,是您生产组装电池的理想设备;

  3、控制电路采用可控硅放电的脉冲电路和数字程序控制电路。各项参数均为数码化设置,因而参数调节直观准确;

  4、焊针的压力和两针的距离可独立调节,且调节方便,确保焊接压力稳定可靠;

  5、焊接开关是国内仅有采用的光电开关;

      点焊机系采用双面双点过流焊接的原理,工作时两个电极加压工件使两层金属在两电极的压力下形成一定的接触电阻,而焊接电流从一电极流经另一电极时在两接触电阻点形成瞬间的热熔接,且焊接电流瞬间从另一电极沿两工件流至此电极形成回路,并且不会伤及被焊工件的内部结构。

      使用方法:

1、焊接时应先调节电极杆的位置,使电极刚好压到焊件时,电极臂保持互相平行。

2、电流调节开关级数的选择可按焊件厚度与材质而选定。通电后电源指示灯应亮,电极压力大小可调整弹簧压力螺母,改变其压缩程度而获得。

3、在完成上述调整后,可先接通冷却水后再接通电源准备焊接。焊接过程的程序:焊件置于两电极之间,踩下脚踏板,并使上电极与焊件接触并加压,在继续压下脚踏板时,电源触头开关接通,于是变压器开始工作次级回路通电使焊件加热。当焊接一定时间后松开脚踏板时电极上升,借弹簧的拉力先切断电源而后恢复原状,单点焊接过程即告结束。


上一条:第一篇   下一条:点焊机应用漆包线行业

咨询热线 0769-82220109

龙生:13392355756    刘生:18681162537 邮箱:517451436@qq.com 地址:广东省东莞市大朗镇松湖云谷创意产业园绩溪楼102-103
龙生
刘生